Production Engineering objective questions with answers part3

Q1. The amount deducted from the salary of workers towards employees provident fund is
(A) credited into reserves of company
(B) deposited in nationalised bank
(C) deposited in the account of worker with employer or Reserve Bank of India
(D) deposited in the account of worker with Provident Fund Commissioner

Q2. The deductions for, employees provident fund start
(A) immediately on joining the service
(B) after 60 days of joining the service
(C) after 100 days of joining the service
(D) after 240 days of joining the service

Q3. Tick the odd man out
(A) Taylor
(B) Drucker
(C) McGregor
(D) Galileo

Q4. Current assets include
(A) manufacturing plant
(B) manufacturing plant and equipment
(C) inventories
(D) common stock held by the firm

Q5. The objective of time study is to determine the time required to complete a job by
(A) fast worker
(B) average worker
(C) slow worker
(D) new entrant

Q6. Job enrichment technique is applied to
(A) reduce labour monotony
(B) overcome boring and demotivating work
(C) make people happy
(D) All of these

Q7. For ship vessel industry the following layout is best suited
(A) process layout
(B) product layout
(C) fixed position layout
(D) plant layout

Q8. In Halsey 50-50 plan, output standards are established
(A) by time study
(B) from previous production records
(C) from one’s judgement
(D) All of these

Q9. Routing is essential in the following type of industry
(A) assembly industry
(B) process industry
(C) job order industry
(D) mass production industry

Q10. An optimum project schedule implies
(A) optimum utilization of men, machines and materials
(B) lowest possible cost and shortest possible time for project
(C) timely execution of project
(D) to produce best results under given constraints

Q11. A grinding wheel is said to be of _________ if the abrasive grains can be easily dislodged.
(A) Soft grade
(B) Medium grade
(C) Hard grade
(D) None of these

Q12. The high cutting speed and large rake angle of the tool will result in the formation of
(A) Continuous chips
(B) Discontinuous chip
(C) Continuous chips with built up edge
(D) None of these

Q13. The facing is an operation of
(A) Beveling the extreme end of a workpiece
(B) Embossing a diamond shaped pattern on the surface of a workpiece
(C) Reducing the diameter of a workpiece over a very narrow surface
(D) Machining the ends of a workpiece to produce a flat surface square with the axis

Q14. Fixtures are used
(A) For holding and guiding the tool in drilling, reaming or tapping operations
(B) For holding the work in milling, grinding, planing or turning operations
(C) To check the accuracy of workpiece
(D) None of the above

Q15. In a shaper, the length of stroke is increased by
(A) Increasing the centre distance of bull gear and crank pin
(B) Decreasing the centre distance of bull gear and crank pin
(C) Increasing the length of the arm
(D) Decreasing the length of the slot in the slotted lever

Q16. The hole to be drilled for tapping is _________ the outside diameter of the thread on the tap.
(A) Equal to
(B) Smaller than
(C) Greater than
(D) None of these

Q17. The obtuse angle, included between the chisel edge and the lip as viewed from the end of a drill, is called
(A) Helix or rake angle
(B) Point angle
(C) Chisel edge angle
(D) Lip clearance angle

Q18. The lip angle of a single point tool is usually
(A) 20° to 40°
(B) 40° to 60°
(C) 60° to 80°
(D) None of these

Q19. Ceramic cutting tools are
(A) Made by cold pressing of aluminium oxide powder
(B) Available in the form of tips
(C) Brittle and have low bending strength
(D) All of these

Q20. The point angle of a drill, for drilling stainless steel, is
(A) 90°
(B) 118°
(C) 135°
(D) 150°